Korenix JetNet 7852G-4XG Series User Manual Download Page 862

Page: 862 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 862/1568

8.1.2.2

ip dvmrp metric

This command configures the metric for an interface. This value is used in the DVMRP messages as
the cost to reach this network.

Syntax

ip dvmrp metric <value>
no ip dvmrp metric <value>

<value> -

This field has a range of 1 to 31.

no -

This command resets the metric for an interface to the default value. This value is used in the

DVMRP messages as the cost to reach this network.

Default Setting

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands