Korenix JetNet 7852G-4XG Series User Manual Download Page 796

Page: 796 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 796/1568

Network:

IP address of a network entity.

Next Hop:

IP address of the next system that is used when forwarding a packet to the destination

network. An entry of 0.0.0.0 indicates that the router has some non-BGP routes to this network.

Metric:

If shown, the value of the interautonomous system metric.

LocPref:

Local preference value as set with the

set local-preference

route-map configuration

command. The default value is 100.

Path:

Autonomous system paths to the destination network. There can be one entry in this field for

each autonomous system in the path.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands