Korenix JetNet 7852G-4XG Series User Manual Download Page 492

Page: 492 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 492/1568

6.17.1.3

clear eventlog

This command is used to clear the event log, which contains error messages from the system.

Syntax

clear eventlog

Default Setting

None

Command Mode

Privileged Exec

6.17.1.4

clear logging buffered

This command is used to clear the message log maintained by the switch. The message log contains
system trace information.

Syntax

clear logging buffered

Default Setting

None

Command Mode

Privileged Exec

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands