Korenix JetNet 7852G-4XG Series User Manual Download Page 489 | Manualshive

Page: 489 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 489/1568

6.16.2.2

macfilter addsrc

This command adds the interface to the source filter set for the MAC filter with the MAC address of
<macaddr> and VLAN of <vlanid>. The <macaddr> parameter must be specified as a 6-byte
hexadecimal number in the format of b1:b2:b3:b4:b5:b6. The <vlanid> parameter must identify a valid
VLAN.

Syntax

macfilter addsrc <macaddr> <1-4093>
no macfilter addsrc <macaddr> <1-4093>

<macaddr> -

Specified a 6-byte hexadecimal number in the format of b1:b2:b3:b4:b5:b6.

no -

This command removes a port from the source filter set for the MAC filter with the MAC address

of <macaddr> and VLAN of <vlanid>.

Default Setting

None

Command Mode

Interface Config

«
...
487
488
489
490
491
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Garland Pages: 4

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

StorTrends 1312-P

Brand: American Megatrends Pages: 2

Brand: Justec Pages: 61

Brand: Buffalo Pages: 2

Brand: 1&1 Pages: 32

WNFB-265AXI(BT)

Brand: Sparklan Pages: 14

Brand: Galaxy Pages: 30

Brand: Teletronics International Pages: 57

Brand: BWI Pages: 5

Brand: YATO Pages: 96

Brand: ActionTec Pages: 115

Brand: Avaya Pages: 73

Brand: Airlink101 Pages: 46

Brand: Digisol Pages: 22

Brand: Allied Telesis Pages: 2

Brand: Kentrox Pages: 246

Brand: FiberHome Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands