Korenix JetNet 7852G-4XG Series User Manual Download Page 1479 | Manualshive

Page: 1479 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1479/1568

IPv6 Prefix

- Enter the IPv6 Prefix/Prefix Length for the address range for the selected area.

Non-Configurable Data

Area ID

- The OSPFv3 area.

IPv6 Prefix

- The IPv6 Prefix of an address range for the area.

LSDB Type

- The Link Advertisement type for the address range and area.

Advertise

- The Advertisement mode for the address range and area.

Remove

- Check box to remove the particular entry from the table.

Command Buttons

Create

- Send the updated configuration to the switch. Configuration changes take effect

immediately. These changes will not be retained across a power cycle unless a save is performed.
The new address range will be added to the display in the non-configurable data area.

Delete

- Removes the specified address range from the area configuration.

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1477
1478
1479
1480
1481
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: bintec elmeg Pages: 33

Brand: NA Pages: 22

Brand: Netis Pages: 16

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

Brand: Hunter Pages: 2

Brand: INNOSILICON Pages: 11

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands