Korenix JetNet 7852G-4XG Series User Manual Download Page 111

Page: 111 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 111/1568

6.2.5.5

bridge-ext gvrp

This command enables GVRP.

Syntax

bridge-ext gvrp
no bridge-ext gvrp

no -

This command disables GVRP.

Default Setting

Disabled

Command Mode

Global Config

6.2.5.6

bridge-ext gmrp

This command enables GARP Multicast Registration Protocol (GMRP) on the system. The default value
is disabled.

Syntax

bridge-ext gmrp
no bridge-ext gmrp

no -

This command disables GARP Multicast Registration Protocol (GMRP) on the system.

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands