Korenix JetNet 7852G-4XG Series User Manual Download Page 567

Page: 567 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 567/1568

6.21.2.9

match dstip

This command adds to the specified class definition a match condition based on the destination IP
address of a packet.

Syntax

match dstip <ipaddr> <ipmask>

<ipaddr>

specifies an IP address.

ipmask>

specifies an IP address bit mask; note that although similar to a standard subnet mask,

this bit mask need not be contiguous.

Default Setting

None

Command Mode

Class-Map Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands