Korenix JetNet 7852G-4XG Series User Manual Download Page 1193

Page: 1193 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1193/1568

11.3.14.2

MAC filter Summary Page

Non-Configurable Data

MAC Address

- The MAC address of the filter in the format 00:01:1A:B2:53:4D.

VLAN ID

- The VLAN ID associated with the filter.

Source Port Members

- A list of ports to be used for filtering inbound packets.

Command Buttons

Refresh

- Refresh the data on the screen with the present state of the data in the switch

«
...
1191
1192
1193
1194
1195
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands