Korenix JetNet 7852G-4XG Series User Manual Download Page 253

Page: 253 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 253/1568

6.3.14.12

set sflow sampler index

The user can go to the CLI Interface Configuration Mode to configure a new sFlow sampler instance, use
the

sflow sampler <index>

interface configuration command. Use the

no sflow sampler

return to

default setting.

Syntax

sflow sampler <index>
no sflow sampler

Default Setting

None

Command Mode

Interface Config

6.3.14.13

set sflow poller index

The user can go to the CLI Interface Configuration Mode to configure a new sFlow poller instance, use
the

sflow poller <index>

interface configuration command. Use the

no sflow poller

return to default

setting.

Syntax

sflow poller <index>
no sflow poller

Default Setting

None

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands