Korenix JetNet 7852G-4XG Series User Manual Download Page 411

Page: 411 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 411/1568

This command is used to configure the authentication host priority.

Syntax

priority [<priority>]

<priority> -

The valid priority number. Range (0

– 65535)>

Default Setting

Command Mode

TACACS Host Config

6.9.5.3

tacacs-server timeout

This command is used to configure the connection timeout value.

Syntax

tacacs-server timeout [<timeout>]
no tacacs-server timeout

<timeout> -

The connection timeout value. Max timeout (Range: 1 to 30).

no -

This command is used to reset the timeout value to the default value.

Default Setting

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands