Korenix JetNet 7852G-4XG Series User Manual Download Page 756

Page: 756 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 756/1568

7.9

Virtual Router Redundancy Protocol (VRRP) Commands

7.9.1

Show Commands

7.9.1.1

show ip vrrp

This command displays whether VRRP functionality is enabled or disabled. It also displays some
global parameters which are required for monitoring.

Syntax

show ip vrrp

Default Setting

None

Command Mode

Privileged

Exec User

Exec

Display Message

Admin Mode:

Displays the administrative mode for VRRP functionality on the switch.

Router Checksum Errors:

Represents the total number of VRRP packets received with an invalid

VRRP checksum value.

Router Version Errors:

Represents the total number of VRRP packets received with Unknown

or unsupported version number.

Router VRID Errors:

Represents the total number of VRRP packets received with invalid VRID

for this virtual router.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands