Korenix JetNet 7852G-4XG Series User Manual Download Page 383

Page: 383 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 383/1568

6.9.4.35

Captive Portal configuration name

This command configures the name for a captive portal configuration. The name can contain up to 32
alphanumeric characters.

Syntax

name <cp-name>

no name

Default Setting

None

Command Mode

Captive Portal Instance

6.9.4.36

Captive Portal configuration protocol

This command configures the protocol mode for a captive portal configuration. The CP can use HTTP or
HTTPS protocols.

Syntax

protocol <http|https>

Default Setting

http

Command Mode

Captive Portal Instance

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands