Korenix JetNet 7852G-4XG Series User Manual Download Page 134

Page: 134 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 134/1568

6.2.7.11

show ip igmp snooping querier detail

This command display all of IGMP snooping querier information on the system.

Syntax

show ip igmp snooping querier detail

Command Mode

Privilege Exec

Display Information

IGMP Snooping Querier Mode:

Administrative mode for IGMP Snooping. The default is disable.

Querier Address:

Specify the Snooping Querier Address to be used as source address in periodic

IGMP queries. This address is used when no address is configured on the VLAN on which query is
being sent.

IGMP Version:

Specify the IGMP protocol version used in periodic IGMP queries.

Querier Query Interval:

Specify the time interval in seconds between periodic queries sent by the

snooping querier. The Query Interval must be a value in the range of 1 and 1800. The default value
is 60.

Querier Expiry Interval:

Specify the time interval in seconds after which the last querier information

is removed. The Querier Expiry Interval must be a value in the range of 60 and 300. The default
value is 120.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands