manualshive.com logo in svg

Korenix JetNet 7852G-4XG Series, User Manual

The Korenix JetNet 7852G-4XG Series switch offers high performance and reliability for industrial networks. Find the user manual for free download on our website for easy configuration and setup. Gain access to detailed instructions and troubleshooting tips to optimize performance. Download your manual at manualshive.com.

Share
Download
background image

Korenix Technology Co., Ltd.                                           

 

Industrial

 

Layer 3 Managed Ethernet Switch

 

 
 

_____________________________________________________________________________ 

Industrial Layer 3 Managed Ethernet SwitchUser Manual

 

 Page: 724/1568 

7.3.2.45 

ip ospf mtu-ignore 

 

ip ospf mtu-ignore 

command disables OSPF maximum transmission unit (MTU) mismatch detection. 

OSPF Database Description packets specify the size of the largest IP packet that can be sent without 
fragmentation on the interface. W hen a router receives a Database Description packet, it examines 
the MTU advertised by the neighbor. By default, if the MTU is larger than the router can accept, the 
Database Description packet is rejected and the OSPF adjacency is not established. 

no ip ospf

 

mtu-ignore 

command enables the OSPF MTU mismatch detection. 

 

 

Syntax

 

 

ip ospf mtu-ignore 
no ip ospf mtu-ignore 

 

 

Default Setting

 

 

Enable

d 

 

Command Mode

 

 

Interface Config 

 
 
 

 

7.3.2.46 

router-id 

 

router-id 

command sets a 4-digit dotted-decimal number uniquely identifying the router ospf id. The 

<ipaddress> is a configured value. 

 

 

Syntax

 

 

router-id <ipaddress> 

 
 

 

Default Setting

 

 

None 

 

Command Mode

 

 

Router OSPF Config Mode 

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

4RF Aprisa LTE Quick Start Manual preview
Aprisa LTE
Brand: 4RF Pages: 7
H3C SR8800 IM-FW-II Command Reference Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 107
3Com MSR 50 Series Safety Information Manual preview
MSR 50 Series
Brand: 3Com Pages: 12
H3C S9500 Series Operating Manual preview
S9500 Series
Brand: H3C Pages: 16
H3C H3C S3600 Series Datasheet preview
H3C S3600 Series
Brand: H3C Pages: 10
H3C MSR 930 Installation Manual preview
MSR 930
Brand: H3C Pages: 42
H3C MSR 800 Installation, Quick Start preview
MSR 800
Brand: H3C Pages: 2
H3C H3C S7500E Series Instruction Manual preview
H3C S7500E Series
Brand: H3C Pages: 34
H3C MSR Series Manual preview
MSR Series
Brand: H3C Pages: 33
H3C CR16000-F Configuration Manual preview
CR16000-F
Brand: H3C Pages: 14
H3C MSR 3600 Hardware Information And Specifications preview
MSR 3600
Brand: H3C Pages: 56
H3C H3C S7500E Series Configuration Manual preview
H3C S7500E Series
Brand: H3C Pages: 112
H3C S3100-52P Command Manual preview
S3100-52P
Brand: H3C Pages: 15
H3C SR8800 IM-FW-II Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 5
H3C H3C S7500E Series Installation Manual preview
H3C S7500E Series
Brand: H3C Pages: 50
H3C MSR810 Manual preview
MSR810
Brand: H3C Pages: 37
H3C CR16000-F Installation, Quick Start preview
CR16000-F
Brand: H3C Pages: 4
H3C MSR 20-1X Quick Start preview
MSR 20-1X
Brand: H3C Pages: 5

Brands by name

Popular brands

Load more brands