Korenix JetNet 7852G-4XG Series User Manual Download Page 519

Page: 519 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 519/1568

6.17.14

hostname

This command is used to set the prompt string.

Syntax

hostname <prompt_string>

<prompt_string>

- Prompt string.

Default Setting

Korenix

Command Mode

Global Config

6.17.15

quit

This command is used to exit a CLI session.

Syntax

quit

Default Setting

None

Command Mode

Privileged Exec

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands