Korenix JetNet 7852G-4XG Series User Manual Download Page 1222

Page: 1222 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1222/1568

11.3.20.4

Configuring MLD Snooping VLAN Status Page

Non-Configurable Data

VLAN ID

- All VLAN Ids for which the MLD Snooping mode is Enabled.

Admin Mode

- MLD Snooping Mode for VLAN ID.

Fast Leave Admin Mode

- Fast Leave Mode for VLAN ID.

Group Membership Interval

- Group Membership Interval of MLD Snooping for the specified VLAN

ID. Valid range is 2 to 3600.

Maximum Response Time

- Maximum Response Time of MLD Snooping for the specified VLAN ID.

Valid range is 1 to 65. Its value should be greater than group membership interval value.

Multicast Router Expiry Time

- Multicast Router Expiry Time of MLD Snooping for the specified

VLAN ID. Valid range is 0 to 3600.

Command Buttons

Refresh

- Refresh the database and display it again starting with the first entry in the table.

«
...
1220
1221
1222
1223
1224
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands