Korenix JetNet 7852G-4XG Series User Manual Download Page 1456 | Manualshive

Page: 1456 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1456/1568

11.6.12

Managing Loopbacks

11.6.12.1

Configuring Loopbacks Configuration Page

Loopback interfaces can be created, configured and removed on this page.

Configurable Data

Loopback

- Select list of currently configured loopback interfaces. Create is also a valid choice if the

maximum number of loopback interfaces has not been created.

Loopback ID

- When 'Create' is chosen from the Loopback selector this list of available loopback

ID's becomes visible.

Protocol

- Select IPv4 or IPv6 to configure the corresponding attributes on the loopback interface.

IPv6 Mode

- Enable IPv6 on this interface using the IPv6 address. This option is only configurable

prior to specifying an explicit IPv6 address.

IPv6 Address

- Select list of configured IPv6 addresses for the selected Loopback interface. Add is

also a valid choice if the maximum number of addresses has not been configured.

IPv6 Address

- When 'Add' is chosen from the IPv6 Address selector this IPv6 address input field

becomes visible. Address must be entered in the format prefix/length.
The user also has the option to specify the 64-bit extended unique identifier (EUI-64).

IPv4 Address

- The primary IPv4 address for this interface in dotted decimal notation.

IPv4 Subnet Mask

- The primary IPv4 subnet mask for this interface in dotted decimal notation.

Secondary Address

- Select list of configured IPv4 secondary addresses for the selected Loopback

interface. Add Secondary is also a valid choice if the maximum number of secondary addresses has
not been configured. A primary address must be configured before secondary addresses can be
added.

Secondary IP Address

- The secondary ip address for this interface in dotted decimal notation. This

input field is visible only when 'Add Secondary' is selected.

Secondary Subnet Mask

- The secondary subnet mask for this interface in dotted decimal notation.

This input field is visible only when 'Add Secondary' is selected.

Command Buttons

Submit

- Update the system with the values on this screen.

Delete Loopback

- Remove the selected loopback interface.

«
...
1454
1455
1456
1457
1458
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: N-Tron Pages: 101

Brand: Magnat Audio Pages: 2

Brand: Lanpro Pages: 5

Brand: M86 Security Pages: 46

Brand: H3C Pages: 21

Brand: Supermicro Pages: 24

Proventia A1204

Brand: Internet Security Systems Pages: 42

Brand: ICP DAS USA Pages: 8

Brand: Ozenda Pages: 116

Brand: BinTec Pages: 2

Brand: Cayman Systems Pages: 170

Brand: Cisco Pages: 122

Brand: Zte Pages: 128

Brand: QNAP Pages: 55

Brand: KEP Pages: 27

Brand: TCL Pages: 24

Wireless Home Phone Base

Brand: Consumer Cellular Pages: 40

Brand: Billion Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands