Korenix JetNet 7852G-4XG Series User Manual Download Page 774

Page: 774 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 774/1568

7.10.2.3 ip prefix-list description

To apply a text description to a prefix list, use the

ip prefix-list description

command in Global

Configuration mode.

To remove the text description, use the

form of this command.

Syntax

ip prefix-list <list-name> description <text>
no ip prefix-list <list-name> description

Default Setting

No description is configured by default.

Command Mode

Global Config

Parameter

list-name:

The text name of the prefix list.

description text:

Text description of the prefix list. Up to 80 characters.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands