Korenix JetNet 7852G-4XG Series User Manual Download Page 1112

Page: 1112 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1112/1568

11.2.10.3

Viewing Traffic Statistics Page

Use this menu to display CDP traffic statistics.

Non-Configurable Data

Incoming Packet Number

- Received legal CDP packets number from neighbors.

Outgoing Packet Number

- Transmitted CDP packets number from this device.

Error Packet Number

- Received illegal CDP packets number from neighbors.

Command Buttons

Clear Counters

- Clear all the counters, resetting all switch summary and detailed statistics to

default values. The discarded packets count cannot be cleared.

Refresh

- Refresh the data on the screen with the present state of the data in the switch.

«
...
1110
1111
1112
1113
1114
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands