Korenix JetNet 7852G-4XG Series User Manual Download Page 1130 | Manualshive

Page: 1130 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1130/1568

11.2.13.5

Configuring LLDP-MED Remote Device Information Page

Selection Criteria

Local Interface

- Specifies the list of all the ports on which LLDP-MED is enabled.

Non-Configurable Data

Capability Information

- Specifies the supported and enabled capabilities that were received in

MED TLV on this port.

Supported Capabilities

- Specifies supported capabilities that were received in MED TLV on

this port.

Enabled Capabilities

- Specifies enabled capabilities that were received in MED TLV on this

port.

Device Class

- Specifies device class as advertised by the device remotely connected to the

port.

Network Policy Information

- Specifies if network policy TLV is received in the LLDP frames on this

port.

Media Application Type

- Specifies the application type. Types of application types are

unknown, voicesignaling, guestvoice, guestvoicesignalling, softphonevoice, videoconferencing,
streammingvideo, vidoesignalling. Each application type that is received has the VLAN id,
priority, DSCP, tagged bit status and unknown bit status. A port may receive one or many such
application types. If a network policy TLV has been receive on this port only then would this
information be displayed.

VLAN Id

- Specifies the VLAN id associated with a particular policy type.

Priority

- Specifies the priority associated with a particular policy type.

DSCP

- Specifies the DSCP associated with a particular policy type.

Unknown Bit Status

- Specifies the unknown bit associated with a particular policy type.

Tagged Bit Status

- Specifies the tagged bit associated with a particular policy type.

Inventory Information

- Specifies if location TLV is received in LLDP frames on this port.

Hardware Revision

- Specifies hardware version of the remote device.

Firmware Revision

- Specifies Firmware version of the remote device.

Software Revision

- Specifies Software version of the remote device.

Serial Number

- Specifies serial number of the remote device.

«
...
1128
1129
1130
1131
1132
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: T&D Pages: 122

Brand: REXROTH Pages: 68

Brand: DCE Pages: 5

Brand: Lanner Pages: 78

Brand: Juniper Pages: 190

Brand: Justec Pages: 61

Brand: SurfControl Pages: 2

DataPlot CB1224

Brand: B-G Instruments Pages: 4

EtherLink 3C905C-TX

Brand: 3Com Pages: 96

Brand: Intercoax Pages: 2

CloudGen Firewall

Brand: Barracuda Pages: 8

Brand: B&B Electronics Pages: 2

Brand: Acard Pages: 43

Brand: TDT Pages: 8

Brand: RadioLAN Pages: 24

Brand: Supermicro Pages: 16

Facility Explorer

Brand: Johnson Controls Pages: 33

Brand: Crestron Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands