Korenix JetNet 7852G-4XG Series User Manual Download Page 1065

Page: 1065 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1065/1568

11.2.5.4

Viewing Authentication List Summary Page

Non-Configurable Data

Login Authentication List -

Shows the Login authentication profiles.

Enable

Authentication List -

Shows the Enable authentication profiles.

Login/Enable

Method List

- User authentication methods. Possible options are:

(1)

Enable

- uses the enable password for authentication.

(2)

Line

- uses the Line password for authentication.

(3)

Local

- the user's locally stored ID and password will be used for authentication

(4)

None

- the user is not authenticated

(5)

Radius

- the user's ID and password will be authenticated using the RADIUS server instead

of locally

(6)

- the user's ID and password will be authenticated using the server

(7)

LDAP

- the user's ID and password will be authenticated using the LDAP server

The Authentication Lists and Authentication Methods configured for each List of

Console

Telnet

SSH

HTTPS

HTTP

and

DOT1X

are displayed respectively.

Command Buttons

Refresh

- Update the information on the page. Summit- Sends the updated screen to the switch and

causes the changes to take effect on the switch. These changes will not be retained across a power
cycle unless you perform a save.

«
...
1063
1064
1065
1066
1067
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands