Korenix JetNet 7852G-4XG Series User Manual Download Page 221

Page: 221 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 221/1568

6.3.6.2

snmptrap snmpversion

This command configures the version for snmp trap.

Syntax

snmptrap snmpversion <name> <ipAddr|ipv6Addr|hostname> <snmpversion>

<name> -

SNMP trap name (Range: up to 16 case-sensitive alphanumeric characters).

< ipAddr|ipv6Addr|hostname> -

an IPv4 or IPv6 address or hostname of the trap receiver.

<snmpversion>

- SNMP trap version.

Default Setting

Snmpv2

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands