Korenix JetNet 7852G-4XG Series User Manual Download Page 1223

Page: 1223 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1223/1568

11.3.20.5

Configuring MLD Snooping Multicast Router Configuration Page

Selection Criteria

Interface

- The select box lists all Slot/Ports. Select the interface for which you want Multicast Router

to be enabled.

Configurable Data

Multicast Router

- Enable or disable Multicast Router on the selected Slot/Port.

Command Buttons

Submit

- Update the switch with the values you entered.

11.3.20.6

Configuring MLD Snooping Multicast Router Status Page

Selection Criteria

Interface

- The single select box lists all physical and LAG interfaces. Select the interface for which

you want to display the status.

Non-Configurable Data

Multicast Router

- Specifies for the selected interface whether multicast router is enable or

disabled.

Command Buttons

Refresh

- Refresh the database and display it again starting with the first entry in the table.

«
...
1221
1222
1223
1224
1225
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands