Korenix JetNet 7852G-4XG Series User Manual Download Page 1528

Page: 1528 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1528/1568

11.8.7.4

Viewing Interface Summary

Selection Criteria

Interface

- Select the interface for which data is to be displayed.

Non-Configurable Data

Admin Mode

- The administrative mode of PIM-SM interface in the router: either enable or disable.

Protocol State

- The state of PIM in the router: either operational or non-operational.

IP Address

- The IP address of the selected PIM interface.

Net Mask

- The Net Masks of the selected PIM interface.

Hello Interval (secs)

- The frequency (in seconds) at which PIM hello messages are transmitted

on the selected interface.

Join/Prune Interval (secs)

- The frequency (in seconds) at which PIM Join/Prune messages

are transmitted on this PIM interface. This field is always shown with defaults for PIMDM as
configurability is not supported in PIMDM.

DR Priority

- Indicates the DR priority on the PIM interface. This field is supported in PIMSM

only and hence shown for PIMSM only.

BSR Border

- Specifies the BSR border mode on the PIM interface. This field is supported in

PIMSM only and hence shown for PIMSM only.

Designated Router

- The Designated Router on the selected PIM interface. This field is

supported in PIMSM only and hence shown for PIMSM only. This field is displayed only when the
interface is Operational.

Interface Neighbors

Neighbor Count

- The number of PIM neighbors on the selected interface. This field is

displayed only when the interface is Operational.

«
...
1526
1527
1528
1529
1530
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands