Korenix JetNet 7852G-4XG Series User Manual Download Page 467

Page: 467 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 467/1568

6.13.2.3

lldp receive

This command uses to enable the LLDP receive capability.

Syntax

lldp receive
no lldp receive

no -

This command is used to return the reception of LLDPDUs to the default value.

Default Setting

Disabled

Command Mode

Interface Config

6.13.2.4

lldp transmit

This command uses to enable the LLDP advertise capability.

Syntax

lldp transmit
no lldp transmit

no -

This command is used to return the local data transmission capability to the default.

Default Setting

Disabled

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands