Korenix JetNet 7852G-4XG Series User Manual Download Page 398

Page: 398 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 398/1568

6.9.4.65

Captive Portal text for logout instructions

This command is to Captive Portal configuration text for logout instructions.

Syntax

logout-text <UTF-16>

no logout-text

Default Setting

None

Command Mode

Captive Portal Locale Mode

6.9.4.66

Captive Portal text for logout title

This command is to Captive Portal configuration text for logout title.

Syntax

logout-title <UTF-16>

no logout-title

Default Setting

None

Command Mode

Captive Portal Locale Mode

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands