Korenix JetNet 7852G-4XG Series User Manual Download Page 434

Page: 434 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 434/1568

6.10.2

Configuration Commands

6.10.2.1

cdp

This command is used to enable CDP Admin Mode.

Syntax

cdp
no cdp

no -

This command is used to disable CDP Admin Mode.

Default Setting

Enabled

Command Mode

Global Config

6.10.2.2

cdp run

This command is used to enable CDP on a specified interface.

Syntax

cdp run
no cdp run

no -

This command is used to disable CDP on a specified interface.

Default Setting

Enabled

Command Mode

Interface Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands