Korenix JetNet 7852G-4XG Series User Manual Download Page 1277

Page: 1277 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1277/1568

11.4.1.11

Defining each Port Access Privileges Page

Selection Criteria

Interface

- Selects the port to configure.

Configurable Data

Users

- Selects the users that have access to the specified port or ports.

Command Buttons

Submit

- Sends the updated screen to the switch and causes the changes to take effect on the

switch but these changes will not be retained across a power cycle unless a save is performed.

Refresh

- Update the information on the page.

«
...
1275
1276
1277
1278
1279
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands