background image

 

 

TLC3-FCR Engineering Manual

 

 

Doc: 70-00-0198, V3.0 Date: 20120403 

© Vector Controls GmbH, Switzerland 

Page 1 

Subject to alteration 

 
TLC3-FCR  
Intelligent Fan Coil Controller 

Features 

 

The PWM control option reduces room temperature 

fluctuations and energy consumption 

 

Low power energy consumption: < 1W per unit 

 

Temperature control for 2-pipe fan coil systems.  

 

Automatic fan control for three stage fans.  

 

Cost saving option with Economy functionality and set point 

limitations 

 

Control for single stage heating, cooling and fan only 

operation modes 

 

Password protected programmable user and control 

parameters 

o

 

Setpoint range limitation 

o

 

Access control for setpoints, fan speeds and mode 

change 

o

 

Access control for heat/cool change and time 

programs 

o

 

Select your display contents 

o

 

Selectable behavior after return from power failure 

 

Temperature display in Celsius or Fahrenheit 

Deluxe Version: 

 

Clock and time schedule functions with power failure protection 

 

Blue backlight for LCD 

 

Infrared remote controller option:  

With special features for Boost and delayed switching on or off 

Applications 

 

Air Only Systems: Three stage fans for single duct systems with up to one binary output for auxiliary heating 

and cooling devices. 

 

Air/Water Systems: Induction units, fan coil units for 2-pipe systems with one binary output for a spring 

return valve.  

General Description 

The TLC3-FCR is a stand-alone electronic fan coil controller with one control loop. The TLC3-FCR features 1 internal 

NTC temperature sensor and four binary outputs (Relays).  
A detailed parameterization is possible with the use of a simple configuration routine. The TLC3-FCR can be configured 

using the standard operation terminal. No special tools or software is required.  

Ordering 

Item Name 

Item code 

Variant 

Power 

Features 

TLC3-FCR-24 

TLC3-FCR-24-W01 

40-10 0128 
40-10 0128-01 

Standard 

Cooling only 

24VAC/DC 

Fan coil controller with:  
1 TI internal 

3 DO (Relay) Fan control 
1 DO (Relay) Binary valve control 

TLC3-FCR-230 

TLC3-FCR-230-W01 

40-10 0110 
40-10 0110-01 

Standard 

Cooling only 

230VAC 

TLC3-FCR-D-24 
TLC3-FCR-D-24-W01 

40-10 0133 
40-10 0133-01 

Deluxe 
Cooling only 

24VAC/DC 

TLC3-FCR-D-230 

TLC3-FCR-D-230-W01 

40-10 0111 
40-10 0111-01 

Deluxe 

Cooling only 

230VAC 

Selection of actuators and fans 

Binary auxiliary devices: E.g. fans, on/off valves, etc.  Do not directly connect devices that exceed 2(1.2)A. Observe 

startup current on inductive loads! Do not connect more than one fan coil unit to one controller. 

Summary of Contents for TLC3-FCR









Reviews: