![background image](http://html1.mh-extra.com/html/omron/cj1w-nc271-12-2009/cj1w-nc271-12-2009_operation-manual_742348639.webp)
611
List of Error Codes
Appendix D
Example: Position deviation overflow alarm (deviation counter overflow)
Servo Drive alarm display: A.24
The PCU's error code in this example is 4018.
Example: Battery warning
Servo Drive warning display: A.92
The PCU's error code in this example is 4092.
For details on alarm display and warning display numbers, and the difference between Servo Drives and Posi-
tion Control Units, refer to the list in Appendix D List of Error Codes.
W-series and SMARTSTEP Junior Servo Drives
Error code: 40
@@
hex
The boxes (
@@
) indicate the alarm/warning display number for the Servo Drive.
When using an R88D-WN
@
-ML2 W-series Servo Drive with built-in MECHATROLINK-II communications, how-
ever, only the upper two digits of the display number's three digits will be displayed.
The alarms that occur in the Servo Drive correspond to error codes that are detected by the PCU when a
MECHATROLINK communications connection has been established, as shown in the following table.
When using an R88D-WT
@
Servo Drive, the two digits following “A.” in the Servo Drive’s display number in the
table are displayed. When using an R88D-WN
@
-ML2 W-series Servo Drive, three digits are displayed (the
value indicated by the display number box is used to further classify the alarm).
For details on each alarm and countermeasures, refer to the operation manual for the Servo Drive being used.
List of G5-series Alarm Displays
The Servo Drive has built-in protective functions. When a protective function is activated, the Servo Drive turns
OFF the alarm output signal (ALM) and switches to the Servo OFF status.
The alarm code will be displayed on the front panel.
Alarm type
Description
---
Protective function that allows the alarm to be reset, and leaves record in the alarm history.
PR
Protective function that does not allow the alarm to be reset, and requires the control power supply
to be turned OFF and turned ON again after resolving the problem.
X
Protective function that does not leave record in the alarm history.
Servo
Drive
display
PCU
error
code
Alarm
type
Error detection function
Detected error or cause of error
11
400B
X
Control power supply und-
ervoltage
The DC voltage of the main circuit has dropped below the
specified value.
12
400C
---
Overvoltage
The DC voltage of the main circuit is abnormally high.
13
400D
X
Main power supply under-
voltage
The DC voltage of the main circuit is low.
14
400E
PR
Overcurrent
Overcurrent flowed to the IGBT. Servomotor power line
ground fault or short circuit.
15
400F
PR
Servo Drive overheat
The temperature of the Servo Drive radiator exceeded the
specified value.
16
4010
---
Overload
Operation was performed with torque significantly exceeding
the rating for several seconds to several tens of seconds.
18
4012
PR
Regeneration overload
The regenerative energy exceeded the processing capacity
of the regeneration resistor.
21
4015
PR
Encoder communications
error
Communications between the encoder and the Servo Drive
failed for a specified number of times, thereby activating the
error detection function.
23
4017
PR
Encoder communications
data error
Communications error occurred for the data from the
encoder.
Содержание CJ1W-NC271 - 12-2009
