![background image](http://html1.mh-extra.com/html/omron/cj1w-nc271-12-2009/cj1w-nc271-12-2009_operation-manual_742348642.webp)
614
List of Error Codes
Appendix D
(2) When multiple warnings occur, the warning codes are displayed on the front panel in the order of
their priority (shown above). The value read from the network is set.
List of G-series Alarm Displays
The Servo Drive has built-in protective functions. When a protective function is activated, the Servo Drive turns
OFF the alarm output signal (ALM) and switches to the Servo OFF status.
The alarm code will be displayed on the front panel.
Alarm type
Description
---
Protective function that allows the alarm to be reset, and leaves record in the alarm history.
PR
Protective function that does not allow the alarm to be reset, and requires the control power supply
to be turned OFF and turned ON again after resolving the problem.
X
Protective function that does not leave record in the alarm history.
Servo
Drive
display
PCU
error
code
Alarm
type
Error detection function
Detected error or cause of error
A.11
400B
X
Control power supply und-
ervoltage
The DC voltage of the main circuit has dropped below the
specified value.
A.12
400C
---
Overvoltage
The DC voltage of the main circuit is abnormally high.
A.13
400D
X
Main power supply under-
voltage
The DC voltage of the main circuit is low.
A.14
400E
PR
Overcurrent
Overcurrent flowed to the IGBT. Servomotor power line
ground fault or short circuit.
A.15
400F
PR
Servo Drive overheat
The temperature of the Servo Drive radiator exceeded the
specified value.
A.16
4010
---
Overload
Operation was performed with torque significantly exceeding
the rating for several seconds to several tens of seconds.
A.18
4012
PR
Regeneration overload
The regenerative energy exceeded the processing capacity
of the regeneration resistor.
A.21
4015
PR
Encoder communications
error
Communications between the encoder and the Servo Drive
failed for a specified number of times, thereby activating the
error detection function.
A.23
4017
PR
Encoder communications
data error
Communications error occurred for the data from the
encoder.
A.24
4018
---
Deviation counter overflow
The number of position deviation pulses exceeded the Devi-
ation Counter Overflow Level (Pn209).
A.26
401A
---
Overspeed
The rotation speed of the Servomotor exceeded the setting
of the Overspeed Detection Level Setting (Pn073).
A.27
401B
PR
Command error
The operation command resulted in an error.
A.29
401D
---
Internal deviation counter
overflow
The value of the internal deviation counter (internal control
unit) exceeded 2
27
(134217728).
A.34
4022
---
Overrun limit error
The Servomotor exceeded the allowable operating range set
in the Overrun Limit Setting (Pn026) with respect to the posi-
tion command input.
A.36
4024
PR
X
Parameter error
Data in the parameter save area was corrupted when the
data was read from the EEPROM at power-ON.
A.37
4025
PR
X
Parameter corruption
The EEPROM write verification data was corrupted when
the data was read from the EEPROM at power-ON.
A.38
4026
X
Drive prohibit input error
Forward and Reverse Drive Prohibit Inputs (NOT and POT)
both became OPEN.
A.40
4028
PR
Absolute encoder system
down error
The voltage supplied to the absolute encoder dropped below
the specified value.
A.41
4029
PR
Absolute encoder counter
overflow error
The multi-turn counter of the absolute encoder exceeded
the specified value.
Содержание CJ1W-NC271 - 12-2009
