![background image](http://html1.mh-extra.com/html/gima/35306/35306_manual_2228144163.webp)
163
ENGLISH
B Status/Error during ECG, SpO
2
, NIBP Monitoring
“Cuff error”
cuff is not wrapped correctly, or is not connected
“Air leak”
Air moving part, tube or the cuff leak air.
“Pressure error”
Unstable cuff pressure or tangled cuff tubing
“Signal weak”
Very weak signal because of the cuff, or the patient has very weak pulse
“Over extent”
The measurement range exceeds 255 mmHg (Pediatric patient over 135
mmHg)
“Over motion”
The repeated measurement due to moving, excessive noise during the
stepping inflation and measuring pressure and pulse, e.g. during patient
shaking motion
“Signal overflow”
Blood pressure amplifier overflow due to excessive movement
“Leak in gas run”
Leaking during the pneumatic device testing
“System error”
Abnormal condition of CPU, such as register overflow, divided by zero
“Adult”
The blood pressure measuring now is in adult mode. In this case, it is not
allowed to monitoring Pediatric or neonatal patient. Otherwise, there may be
serious danger to the Pediatric monitored.
“Pediatric”
The blood pressure module is now worked in Pediatric measuring mode.
“PROBE OFF”
SpO
2
probe fell off
“LEADS OFF”
The ECG electrodes or cable fell off
“LEARNING”
Learning arrhythmia for 15 seconds
“DEMO”
The monitor is displaying the demo waveforms, which are generated by the
monitor itself.
C Status/Error during CO
2
Monitoring
Suggested Message/Response
Description
“Sensor Over Temp”
Make sure sensor is not exposed to extreme heat (heat
lamp, etc.). If error persists, return sensor to factory for
servicing.
The sensor temperature is greater than 40 °C.
“Sensor Faulty”
Check that the sensor is properly plugged in. Reinsert
or reset the sensor if necessary. If error persists, return
sensor to factory for servicing
One of the following conditions exist:
Source Current Failure,
EEPROM Checksum Faulty,
Hardware Error
No Parameter Message
The host must set the Barometric Pressure and
compensations to clear this error; no user intervention
should be required.
Barometric Pressure and/or gas compensations have not
been set since power on. For CO
2
to be calculated with
the stated accuracy, these values should be set whenever
the sensor is plugged in.
“Module in Sleep Mode”
This bit is set when sensor has been placed in sleep
mode.
Содержание 35306
