Woodward easYgen-3000XT Series, Manual, Page: 33 / 1205

Rev. Date Editor Changes
◦ 5014, start addr. 450136, ID 4090 ◦
• LogicsManager References update: •
◦ 07.xx: IDs changed ◦
◦ 09.xx: IDs changed
◦
◦ 10.xx: IDs changed
◦
◦ 11.xx: IDs changed
◦
◦ 13.xx: IDs changed
◦
◦ 15.xx: IDs changed
◦
• Layout optimizations and typo corrections. •
E 2016-12 GG NEW Software Revision Release 1.13 or higher
NEW features & functions
• A customer specific device name can be entered and will be used e.g. as device •
name in Ethernet network. For more details refer to ╚═▷ “4.3.5 System
Management” .
• All monitoring functions in the device are from now on expanded with an •
additional functionality:
◦ Each monitor can be individually enabled by an internal LogicsManager flag. ◦
(For example refer to parameter »Enabled« ╚═▷ “4.5.1.3.2 Generator
Overfrequency (Level 1 & 2) ANSI# 81O” ).
• Device identification via settings file: Serial number will be part of the .wset file •
generated and saved via ToolKit. Device identification, file management, and
support request become much easier.
• AnalogManager became even more flexible: •
◦ 16 free configurable and accessible constants enable pre-sets to be used as ◦
AnalogManager input. For details refer to ╚═▷ “4.9.2 AnalogManager
Constants” .
• »Generator Total AC Power« PGN 65029 is send to Scania S6 ECU via J1939 •
protocol. For details refer to ╚═▷ “7.5.3 Device Types "Standard" and "Standard
C"” .
• Power factor values display (generator and mains) enhanced: Three instead two •
decimal places. Refer to ╚═▷ “8.3 Accuracy” for details.
• Fuel level monitoring offers two further SPN available via J1939 interface (refer to •
╚═▷ “Standard visualization messages” ) and ╚═▷ “9.2.7 Protocol 5016 (Basic
Visualization)” :
◦ SPN 96: 96:Fuel level 1 ◦
◦ SPN 38: 09.15 38:Fuel level 2
◦
• The "Protection Lamp DM1" status of the J1939 communication is from now on •
available as LogicsManager command variable "03.44 Protection lamp DM1". Refer
to
╚═▷ “9.3.2.3 Group 03: Engine control” for details.
• Max number of logged events enhanced: 1000 events saved now instead of 300 •
before. Refer to ╚═▷ “9.5.2 Event History” for details.
• The frequency measurements based on phase-phase and phase-neutral voltages •
are monitored on plausibility. For details refer to ╚═▷ “4.5.1.3.1 Plausibility Check
of Voltages' AC Wiring” .
• Both alarm class configuration parameters ╚═▷ 2601 for GCB and ╚═▷ 2621 for •
MCB now additionally offer the possibility to select "Control".
• The device stores from now on the three generator current slave pointers in a non- •
volatile memory.
• The breaker closed transition time in the mode GCB/MCB has been optimized to •
match the <100 ms duration time. Refer to ╚═▷ “Breaker logic "CLOSED
TRANSIT."” for details.
• The Node-ID of the device in a CAN bus network can be automatically pre-set with •
the device number. Parameter ╚═▷ 1894 »Align device no. with Node-ID« must be
configured to "Yes". This will avoid same-number-mismatch.
• Load sharing interface can be switched between CAN and Ethernet. Refer to •
parameter »Load share interface« ╚═▷ 9924 for details.
• Island mode: •
33 easYgen-3000XT Series B37574
1 General Information
1.1 Revision History
Released