Woodward easYgen-3000XT Series, Manual, Page: 27 / 1205

Rev. Date Editor Changes
• Modbus Master uses always the port number 501 instead of the configured one. •
This is fixed now.
K 2020-09 TM NEW Software Revision Release 2.10-1 or higher
NEW features & functions
• The AnalogManager variables "Free analog values" 24.05 to 24.08 are write- •
protected with code level CL1. ╚═▷ “9.4.2.15 Group 24: Free analog values”
• In operation mode MANUAL the discrete raise/lower function is now available with •
configurable ramp rates. ╚═▷ “4.4.4.7 Discrete Raise/Low Function”
• Expansion of the "Mains Voltage increase" monitor on up to 6 phases. •
• To reach the component certification VDE-AR-N 4105 the password code level of
•
some mains decoupling parameter are changed:
◦ Mains voltage increase limit ID8807 from code level CL2 to CL1 ╚═▷ 8807 ◦
◦ Mains undervoltage 1 delay time ID3005 from code level CL2 to CL1
╚═▷ ◦
3005
◦ Mains undervoltage 2 delay time ID3011 from code level CL2 to CL1 ╚═▷ ◦
3011
• The CANopen-Interface-3 error flag was missing in the modbus protocol 5016 and •
is now available. ╚═▷ “The following data protocols are implemented to be used”
• Introduction of a Ethernet Address Network Check. ╚═▷ “4.7.5 Ethernet Interfaces” •
• Expansion of the J1939 ECU handling. Introduction of a new sequencer file
•
"Volvo_EMS_1.3_49058". ╚═▷ “4.7.4.2.2 J1939 Interface”
Corrections/Repairs
• The Parameter ID511 "Remote reactive power setpoint" is getting the format •
(Signed INT32). This allows now to send negative kvar setpoints to the easYgen.
• Start counter: Counter is now working too if changed from STOP to AUTO or TEST •
during Start req. in AUTO is already true and if there is no preglow.
• The generator excitation limiter function and indication is disabled if reactive •
control in the device is disabled.
• In cases the easYgen runs the genset with breaker transition mode "Open •
transition": It could lead under special circumstances that the mains settling time
is shortened to 2 seconds even there is no need for. This is fixed now.
• In cases the operation mode is configured in order not to go automatically into •
STOP due to a shutdown alarm and a MCB closure failure shall cause an
emergency run: It could lead under special circumstances that the emergency run
state in the event logger is steadily retriggered. This is fixed now.
J 2020-04 TM NEW Software Revision Release 2.10 or higher
NEW features & functions
• Introduction of a Modbus Master functionality. ╚═▷ “6.5.5 Modbus master” •
• Introduction of a Photovoltaic (PV) inverter load reduction function including of a
•
monitor feature. ╚═▷ “4.4.4.5.6 Photovoltaic (PV) load reduction regulated mode”
• Separate parameters for mains over/under voltage and over/under frequency •
hysteresis.
• Writing LDSS Reserve power into the device: The device allows now a remotely •
frequently refreshed reserve power setting.
IOP: ╚═▷ “Remote LDSS IOP reserve power ”
MOP ╚═▷ “Remote LDSS MOP reserve power ”
• Providing of a monitoring function for Ethernet issues. ╚═▷ “4.5.6.12 Ethernet •
interfaces”
• LDSS: The current reserve power setting (Parameter, LM Parameter or from RAM •
variable) is indicated in the ToolKit Status "States easYgen / Sequencing" screen.
• The easYgen provides a "Reboot" parameter in ToolKit and HMI. ╚═▷ “4.3.5.1 •
Reboot Function”
• Communication protocols 5014 and 5016 are updated with •
27 easYgen-3000XT Series B37574
1 General Information
1.1 Revision History
Released