Mazda MX-6 1998 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL FS]

STEP

INSPECTION

ACTION

4

CHECK FOR UNMETERED AIR LEAKS
Fuel calculations can be affected by
unmetered air leaks.

•

Carefully inspect the following areas for

potential air leaks.

•

Hoses connecting to MAF sensor

•

Hoses connecting to throttle body

•

Intake manifold gasket leaks

•

Positive crankcase ventilation (PCV)

disconnected

•

Vacuum lines disconnected

•

Improperly seated engine oil dipstick

and tube

•

Exhaust leaks at flanges and gaskets

• Are there any air leaks?

Yes

Air leaks located.
SERVICE source of air leak.

RESET PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

No

Go to next step.

5

CHECK OF HEATED OXYGEN SENSOR
CIRCUIT WIRING WITH PCM CONNECTED

•

Key off.

•

PCM connected.

•

Disconnect suspected heated oxygen

sensor.

•

Jumper heated oxygen sensor signal circuit

to power circuit at heated oxygen sensor

harness connector.

•

NGS tester connected.

•

Key on, engine off.

•

Access correct heated oxygen sensor PID.

•

02S11

Note
•

Heated oxygen sensor displayed as 02S11

(Front), 0 2 S 1 2 (REAR) on NGS tester.

• Is voltage greater than 1.50 volts?

Yes

Heated oxygen  sensor signal circuit is  not faulty.
REPLACE  heated oxygen sensor.
CHANGE  oil/filter.
RESET  PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

No

Go to next step.

6

CHECK RESISTANCE OF HEATED OXYGEN
SENSOR  SIGNAL CIRCUIT
•   Key off.
•   Disconnect NGS tester.
•   Disconnect  PCM.  Inspect both  end of

connect for bent or pushed out pins,
corrosion or other damage. Service as

necessary.

• Install breakout box. Leave PCM

disconnected.

• Measure resistance between heated

oxygen sensor signal Test Pin at breakout
box and heated oxygen sensor harness
connector.
• H 02S Front=Test Pin 60

• Measure resistance between following Test

Pin at breakout box and heated oxygen

sensor harness connector.
• Ground=Test Pin 91

•

Is resistance less than 5.0 ohms?

Yes

Go to next step.

No

Resistance is high.

SERVICE open circuit.

REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

7

CHECK  FOR  SHORT  IN  HEATED  OXYGEN
SENSOR  CIRCUIT
•   Key off.
•   Breakout box installed.  PCM disconnected.
•   Measure  resistance between  heated

oxygen sensor signal Test Pin at breakout
box and power circuit and heated oxygen

sensor signal Test Pin and ground circuit at

breakout box.
•   H 02S   (Front)=Test  Pin  60
•   Power circuit=Test  Pin  71/97
•   Ground=Test  Pin 91

•

Is resistance greater than 10,000 ohms?

Yes

REPLACE  PCM.
COMPLETE OBD  II  Drive  Mode.
RERUN  OBD Test.

No

SERVICE short circuit.

REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

tr

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

0 1 -0 1 A -2 7

«
...
53
54
55
56
57
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Yakima Страницы: 11

Бренд: Gator Страницы: 2

Бренд: ULTIMATE SPEED Страницы: 21

Бренд: Nuna Страницы: 17

Бренд: Meta System Страницы: 16

Бренд: Warn Страницы: 5

Бренд: Thule Страницы: 12

Бренд: Camoplast Страницы: 19

Бренд: Havis Страницы: 5

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

PRIME DESIGN VCR-TC11B

Бренд: Safe Fleet Страницы: 12

Бренд: Alphasonik Страницы: 8

Бренд: Mazda Страницы: 3

Бренд: Brink Страницы: 26

Бренд: Thule Страницы: 8

Бренд: Metra Electronics Страницы: 20

3 Facelift 2006

Бренд: Mazda Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды