AUTOMATIC TRANSAXLE [GF4A-EL]
TRANSAXLE RANGE SWITCH ADJUSTMENT [GF4A-EL]
1. Disconnect the negative battery cable.
2. Remove the resonance chamber, fresh-air duct,
and air cleaner component. (Refer to 01 - 1 3B
INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [KL].)
3. Remove the spring pin and clip and disconnect
the selector cable.
4. Rotate the manual shaft to N position.
5. Disconnect the transaxle range switch connector.
6. Loosen the transaxle range switch mounting bolts.
7. Connect an ohmmeter between terminals A and
H.
W 6 U 5 1 7 W D 8
8. Adjust the switch to the point where there is
continuity between the terminals.
9. Tighten the transaxle range switch mounting bolts.
W 6 U 5 1 7 W 4 0
Tightening torque
7.9— 10.7 N m
(80— 110 kgf cm, 69.5— 95.4 in lbf}
10. Verify that the selector lever range position and
transaxle range switch are aligned.
11. Connect the transaxle range switch connector.
12. Connect the selector cable and install a new
spring pin and clip.
13. Install the air cleaner component, fresh-air duct,
and resonance chamber. (Refer to 0 1 -1 3B
INTAKE-AIR SYSTEM
REMOVAL/INSTALLATION [KL].)
14. Connect the negative battery cable.
TRANSAXLE FLUID TEMPERATURE SENSOR INSPECTION [GF4A-EL]
1. Remove the transaxle fluid temperature sensor.
(Refer to 0 5 -1 7B TRANSAXLE FLUID
TEMPERATURE REMOVAL/INSTALLATION
[GF4A-EL].)
W 6 U 5 1 7 W 2 0
20 (68)
2.441— 2.894
40 (1 0 4 }
1.193— 1.374
60(140}
0.6284— 0.7048
80(176}
0.3527— 0.3865
100 (212}
0.2091—0.2245
120 (248}
0.1301— 0.1372
130 (266}
0.1044— 0.1090
2. Place the transaxle fluid temperature sensor in
ATF with a thermometer as shown and heat the
ATF gradually. Do not allow the test pieces to
touch the bottom.
3. Measure resistance between the terminals of the
transaxle fluid temperature sensor.
V I
A
. J
ATF te m p e ra tu re f C { ’ F})
R esistance (k£2)
- 2 0 (-4 )
13.47— 17.17
0 (3 2 }
5.445— 6.678
W 6 U 5 1 7 W D B
4. If not correct, replace the transaxle fluid
temperature sensor.
5. Install the transaxle temperature sensor. (Refer to
0 5 -1 7B TRANSAXLE TEMPERATURE SENSOR
REMOVAL/INSTALLATION [GF4A-EL].)
TRANSAXLE
FLUID
TEMPERATURE
SENSOR
W 6 U 5 1 7 W D A
0 5 -1 7 B -1 3
Содержание MX-6 1998
