Mazda MX-6 1998 Скачать руководство пользователя страница 966 | Manualshive

Страница: 966 / 1282

background image

TROUBLESHOOTING [SEAT BELT]

3

Seat belt warning light illuminates but warning buzzer does not sound

TROUBLESHOOTING HINTS

Malfunction in seat belt warning buzzer input signal circuit

© Seat belt warning buzzer does not sound

• CPU malfunction
• Malfunction in wiring harness between CPU and buckle switch

Malfunction in CPU power supply/ground circuit

(?) Seat belt warning buzzer does not sound

• Malfunction in wiring harness between METER 10 A fuse and CPU
• Malfunction in wiring harness between ROOM 15 A fuse and CPU

• Malfunction in wiring harness between CPU and ground

• ROOM 15 A fuse malfunction

STEP

INSPECTION

ACTION

Is ROOM 15 A fuse okay?

Yes

Go to next step.

No

Replace fuse after repairing wiring harness.

Has seat belt warning buzzer sounded for

4 to

8

seconds

since turning ignition switch to

ON?

Yes

Seat belt warning system is okay.

No

Go to next step.

Disconnect negative battery cable.
Remove driver’s side front scuff plate.
Remove driver’s side front side trim.
Remove nuts fixed in joint box and remove
CPU from joint box.

Connect negative battery cable.
Turn ignition switch to ON.

Measure voltage at terminal 1M at joint box of

wiring harness.

Is voltage

B+?

Yes

Go to next step.

No

Repair wiring harness between METER 10 A fuse and

CPU.

Measure voltage at terminal 1J at joint box of
wiring harness.

Is voltage

B+?

Yes

Go to next step.

No

Repair wiring harness between ROOM 15 A fuse and joint
box.

0 8 -0 1 B -3

«
...
964
965
966
967
968
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Daewoo Страницы: 68

Бренд: Hyundai Страницы: 437

Бренд: Chevrolet Страницы: 376

Бренд: Mazda Страницы: 15

ULTIMATE SPEED 296713

Бренд: walser Страницы: 10

Бренд: Mercedes-Benz Страницы: 373

Бренд: Prorack Страницы: 15

Dodge Caravan 2002

Бренд: Chrysler Страницы: 2399

Бренд: Ednet Страницы: 6

Бренд: Bulldog Security Страницы: 7

Бренд: Scosche Страницы: 32

Бренд: Mazda Страницы: 605

Бренд: Rosco Страницы: 12

Бренд: Aries Страницы: 6

PRIME DESIGN HRR-NV11B

Бренд: Safe Fleet Страницы: 12

1996 Civic Del Sol

Бренд: Honda Страницы: 219

Sightline VIMMB-85N

Бренд: Crux Страницы: 2

Бренд: Axxess Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды