Mazda MX-6 1998 Скачать руководство пользователя страница 990 | Manualshive

Страница: 990 / 1282

Mazda MX-6 1998 Скачать руководство пользователя страница 990

TROUBLESHOOTING [REAR WINDOW DEFROSTER]

STEP

INSPECTION

ACTION

Remove  meter hood.
Remove  rear window defroster switch without
disconnecting  rear window defroster switch

connector.

Check for continuity between terminal B at
rear window defroster switch connector of

wiring harness and ground with rear window

defroster switch on.

Is there continuity?

W 6 U 9 0 1 W B 4

Yes

Repair wiring harness between CPU and rear window

defroster switch.

No

Go to next step.

Disconnect rear window defroster switch
connector.
Check for continuity between terminal C at
rear window defroster switch connector of
wiring harness and ground.

Is there continuity?

Yes

Replace rear window defroster switch.

No

Repair wiring harness between rear window defroster

switch and ground.

W 6 U 9 0 1 W B 5

Remove rear window defroster relay.

Turn ignition switch to ON.

Measure voltage at terminal A at rear window
defroster relay connector of wiring harness.

Is voltage

B+?

Yes

Go to next step.

No

Repair wiring harness between METER 10 A fuse and
rear window defroster relay.

W 6 U 9 0 1 W B 6

0 9 -0 1 B -3

«
...
988
989
990
991
992
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов