Mazda MX-6 1998 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL FS]

DTC

P0135

P0141

Heated oxygen sensor heater (Front) (HTR 11) circuit malfunction

Heated oxygen sensor heater (Rear) (HTR 12) circuit malfunction

DESCRIPTION

• DTC P0135 and P0141 indicate short to ground, or open, or short to power circuit in

heated oxygen sensor heater circuit

[Possible Cause]

• Shorts to B+ in harness or heated oxygen sensor

• Open ground circuit

• W ater in connectors

• Low battery positive voltage

• Cut or pulled wires

• Corrosion or poor mating terminals

• Disconnected wiring

• Damaged heated oxygen sensor heater

• Open heated oxygen sensor heater power circuit

• Damaged PCM

STEP

INSPECTION

ACTION

1

HEATED OXYGEN SENSOR HEATER

SIGNAL CIRCUIT IS OPEN, SHORTED TO

GROUND,  SHORTED TO  B+  OR
EXCESSIVE  CURRENT  DRAW
Heated oxygen  sensor reference list
DTC  P0135=Heated oxygen sensor heater
(Front)
DTC  P0141=Heated oxygen sensor heater
(Rear)
•   Visually inspect heated oxygen sensor

circuit for exposed wiring, contamination,
corrosion and proper assembly.

Note

• On some applications, vehicle hoist may be

required to access heated oxygen sensor
harness.

•

Were any concerns found during visual

inspection?

Yes

SERVICE any concerns found in the visual inspection.

RESET PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE a OBD II Drive Mode.

RERUN OBD Test.

No

Go to next step.

2

PERFORM KOEO SELF TEST

• Key off.

• NGS tester connected.
• Key on, engine on.

• Engine at 2,000 rpm for

1

minute.

• Key off.

• Key on, engine off.
• Perform KOEO self-test.

•

Are DTCs P0135 and/or P0141 present?

Yes

Go to next step.

No

Fault  may be  intermittent.
Intermittent poor connection  or component malfunction
(SERVICE or REPLACE as necessary).
Go to  ENGINE SYMPTOM TROUBLESHOOTING  No.27

3

CHECK  FOR  POWER  AT  VEHICLE  HEATED
OXYGEN  SENSOR  HARNESS
CONNECTOR
•   Key off.

• Disconnect appropriate heated oxygen

sensor(s).

• Inspect both ends of connector(s) for

damaged or pushed out pins, moisture,

corrosion, contamination, etc. Repair as

necessary.

• Key on, engine off.
• Measure voltage between power and

ground circuit at heated oxygen sensor

vehicle harness connector.

• Is voltage greater than 10.5 volts?

Yes

Go to step 5.

No

Go to next step.

0 1 -0 1 A -2 8

«
...
54
55
56
57
58
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: iDataLink Страницы: 9

Бренд: Feniex Страницы: 6

Бренд: Lancia Страницы: 386

Бренд: Doug Thorley Headers Страницы: 5

Бренд: Edelbrock Страницы: 2

Бренд: Whispbar Страницы: 15

2012 Truck Chassis cab

Бренд: RAM Страницы: 506

Бренд: Pacbrake Страницы: 6

Бренд: r.LiNK Страницы: 21

Бренд: RAM Страницы: 330

Бренд: Scosche Страницы: 8

Бренд: JBA Страницы: 5

Бренд: Belkin Страницы: 30

Бренд: Mitsubishi Страницы: 141

Бренд: Great day Страницы: 5

Бренд: Cadillac Страницы: 339

Бренд: Velleman Страницы: 17

Бренд: AUTOTECH Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды