Mazda MX-6 1998 Скачать руководство пользователя страница 83

Страница: 83 / 1282

TROUBLESHOOTING [ENGINE CONTROL FS]

STEP

INSPECTION

ACTION

CHECK EGR VALVE CIRCUIT CONTINUITY

• Key off.
• Disconnect PCM. Inspect for damaged or

pushed out pins, corrosion, loose wires,
etc. Service as necessary.

• Install breakout box. Leave PCM

disconnected.

• Measure resistance between EGR valve

Test Pin at the breakout box and EGR
valve vehicle harness connector. Record

readings.

Test pin

EGR valve terminal

W 6 U 1 0 1 W D 3

• Is each resistance less than 5.0 ohms?

Yes

Go to next step.

SERVICE open in EGR valve harness circuit.
REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

tsr

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

CHECK EGR VALVE CIRCUIT FOR SHORT

TO POWER AND SHORT TO GROUND

•   Key off.
•   EGR  valve disconnected.
•   Breakout box installed.
•   Measure  resistance between Test  Pins 46,

56, 68, 72 and Test Pins 71, 97 and 90 at
breakout box.

• Measure resistance between Test Pins 46,

56, 68, 72 and Test Pins 51,103 and 91 at
breakout box.

• Is each resistance greater than 10,000

ohms?

Yes

REPLACE EGR valve.
REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

SERVICE short in EGR valve harness circuit.

REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

CHECK  POWER  CIRCUIT TO  EGR  BOOST
SOLENOID  VALVE
•   Key off.
•   EGR  boost solenoid valve disconnected.
•   Key on,  engine off.

• Measure voltage between power circuit

and chassis ground at EGR boost solenoid

valve vehicle harness connector.

• Is EGR boost solenoid valve power

circuit voltage greater than 10.5 volts?

Yes

Go to next step.

SERVICE open in EGR boost solenoid valve power circuit.

RECONNECT all components.
RESET PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

CHECK  RESISTANCE  OF  EGR  BOOST
SOLENOID  VALVE
•   Key off.
•   EGR boost solenoid valve disconnected.
•   Measure  EGR boost solenoid valve

resistance.

• Is resistance between 30 and 70 ohms?

Yes

Go to next step.

REPLACE EGR boost solenoid valve.
RESET PCM to completely clear DTCs.

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

CHECK EGR BOOST SOLENOID VALVE

CIRCUIT CONTINUITY

•   Key off.
•   EGR boost solenoid valve disconnected.
•   Disconnect  PCM.  Inspect for damaged or

pushed out pins, corrosion, loose wires,
etc. Service as necessary.

• Install breakout box.
• Measure resistance between Test Pin 98 at

breakout box and EGR boost solenoid
valve circuit at vehicle harness connector.

• Is resistance less than 5.0 ohms?

Yes

Go to next step.

SERVICE open in EGR boost solenoid valve harness
circuit.

REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

0 1 -0 1 A -5 5

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды