Mazda MX-6 1998, Руководство по ремонту

Страница: 210 / 1282

TROUBLESHOOTING [ENGINE CONTROL KL]
I I
R E A D .'C I F A R C O N T IN U O U S D T C ''.
KOEO ON -D EM AN D S ELF-T E S T
KOER ON -D EM AN D S ELF-TEST
ON BOARD SYSTEM READINESS TESTS
SELECT I TEH AND PRESS TRIGGER TO START
R E A D /C I E A R C O N T IN U O U S D T C s I
K O E O O N D E M A N D S E L F T E S T
KOER O N -DEM AND S ELF-TE ST
ON BOARD SYSTEM READINESS TESTS
SELECT ITEM ANO PRESS TRIGGER TO START
W6U101WK7 W6U101WK9
4. Follow operating instruction from the menu.
Read/clear continuous DTC self-test procedure 5. Note any KOEO DTCs. Press CANCEL. Perform
KOER Self-Test.
Note
• The first test to run is Read/Clear Continuous
DTC Self-Test. Record the DTCs on a piece of
paper and proceed to the KOEO Self-Test.
• The purpose of recording the continuous
DTCs at this time to make sure they are not
unintentionally cleared during any KOEO or
KOER service. KOEO and KOER codes are
always addressed before continuous codes.
1. Perform the “New generation star (NGS) tester
hook-up procedure".
2. Perform the “ Reading DTCs procedure”.
3. Move the cursor to READ/CLEAR CONTINUOUS
DTCs. Press the trigger key to enter this
selection.
KOEO O N-DEM AND SELF-TE ST
KOER O N -DEM AND S ELF-TEST
ON BOARD SYSTEM READINESS TESTS
SELECT ITE« ANO PRESS TRIGGER TO START
Key ON engine running self-test procedure
Note
• Make sure the A/C switch is OFF during
KOER Self-Test. If the A/C switch is ON
during this test, DTC P1464 will be indicated
on the NGS tester.
• The brake pedal must be depressed and
released after KOER Self-Test is initiated. If
not performed, DTC P1703 will be indicated
on the NGS tester.
• The steering wheel must be turned to the right
and left after KOER Self-Test is initiated. If not
performed, DTC P1650 will be indicated on
the NGS tester.
• Start the engine and bring up to normal
operating temperature before running the
KOER Self-Test.
1. Perform the “New generation star (NGS) tester
hook-up procedure”.
2. Perform the “Reading DTCs procedure”.
3. Move the cursor to
KOER ON-DEMAND
SELF-TEST. Press the trigger to enter this
selection.
W6U101WK8
4. Turn key on. Press START.
5. Follow operating instruction from the menu.
6. If there are DTC(s), refer to Diagnostic Trouble
Code Table for further diagnosis information. After
repairs, clear DTCs. Press
“C-ALL” (Key #7)
button and press trigger.
7. If there are no codes, press CANCEL. Perform
KOEO Self-Test.
Key ON engine OFF self-test procedure
1. Perform the “New generation star (NGS) tester
hook-up procedure” .
2. Perform the “ Reading DTCs procedure” .
3. Move the cursor to KOEO ON-DEMAND
SELF-TEST. Press the trigger key to enter this
selection.
READ/CLEAR CONTINUOUS DTCs
KOEO O N -DEM AND S ELF-TE ST
K O L H O N D E M A N D S E L F T E S T
ON BOARD SYSTEM READINESS TESTS
SELECT ITEM ANO PRESS TRIGGER TO START
W6U101WKA
4. Start engine and bring up to normal operating
temperature. Press START.
5. Follow operating instruction from the menu and
perform Brake On/Off (BOO), O/D OFF switch
and PSP cycling test, if equipped.
6. Note any KOER DTCs.
7. Press
CANCEL several times to return to the
main menu.
01-01B-4