Mazda MX-6 1998 Скачать руководство пользователя страница 1121 | Manualshive

Страница: 1121 / 1282

background image

TROUBLESHOOTING [INSTRUMENTATION/DRIVER INFO.]

15

Door ajar warning light does not illuminate with any door open

TROUBLESHOOTING HINTS

Malfunction in CPU power supply/ground circuit

© Door ajar warning light does not illuminate

•   ROOM  15 A fuse malfunction
•   CPU  malfunction
•   Malfunction  in wiring harness between  ROOM  15 A fuse and CPU
•   Malfunction  in wiring  harness between  CPU  and ground

Malfunction in door ajar warning light input signal circuit

© Door ajar warning light does not illuminate

•   Door switch malfunction
•   CPU  malfunction
•   Malfunction  in wiring harness between  CPU  and door switch

Malfunction in door ajar warning light operation circuit

© Door ajar warning light does not illuminate

•   CPU  malfunction
•   Door ajar warning light bulb malfunction
•   Print plate  malfunction
•   Malfunction  in wiring harness between instrument cluster and CPU

STEP

INSPECTION

ACTION

Turn interior light switch to DOOR position.

Open any door.

Does interior light illuminate?

Yes

Go to step 7.

No

Go to next step.

Is ROOM 15 A fuse okay?

Yes

Go to next step.

No

Replace fuse after repairing wiring harness.

W6U901WVS

Remove driver’s side front scuff plate.
Remove driver’s side front side trim.
Remove nut fixed in joint box and  remove
CPU  from joint box.
Measure voltage at terminal  1J  at joint box
(16-pin).
Is voltage

B+?

Yes

Go to next step.

No

Repair wiring harness between ROOM 15 A fuse and

CPU.

0 9 -0 1 P -2 5

«
...
1119
1120
1121
1122
1123
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Kargo Master Страницы: 5

21 COVERT Series

Бренд: Code 3 Страницы: 16

Бренд: Sears Страницы: 41

Бренд: SCC Страницы: 4

Бренд: SAN HIMA Страницы: 10

Бренд: JKS Страницы: 6

Бренд: Subaru Страницы: 32

Бренд: Honda Страницы: 569

PRIME DESIGN VCR-TC11B

Бренд: Safe Fleet Страницы: 12

Бренд: Edelbrock Страницы: 2

Бренд: Hudson Страницы: 77

Бренд: Kargo Master Страницы: 18

Бренд: Buick Страницы: 20

Turnoverball 1020

Бренд: Bowers & Wilkins Страницы: 6

Бренд: FAAFTECH Страницы: 2

Бренд: Camcar Страницы: 2

V-520 RT Series

Бренд: Thermo King Страницы: 56

Бренд: AutoMaxi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды