manualshive.com logo in svg

Mazda MX-6 1998, Руководство по ремонту, Страница: 1111 / 1282

Поделиться
Скачать
Mazda MX-6 1998 Скачать руководство пользователя страница 1111

TROUBLESHOOTING [INSTRUMENTATION/DRIVER INFO.]

8 

Ail  warning  lights do  not illuminate with  ignition  switch at ON  (engine stopped)

TROUBLESHOOTING  HINTS

Malfunction  in  instrument cluster power supply 

0  Warning lights do not illuminate

•   METER  10 A fuse malfunction
•   Print plate malfunction
•   Malfunction in wiring harness between  METER  10 A  fuse and instrument cluster

STEP

INSPECTION

ACTION

Is  METER  10 A fuse okay?

Yes

Go to next step.

No

Replace fuse after repairing wiring  harness.

Remove meter hood.
Remove instrument cluster.
Measure voltage at terminal 3N at instrument 

cluster (14-pin) connector of wiring harness. 

Is voltage 

B+?

Yes

Replace print plate.

a-

 0 9-22  INSTRUMENT CLUSTER 

DISASSEMBLY/ASSEMBLY

No

Repair wiring  harness between  METER  10 A fuse and 

instrument cluster.

S B

\

3N -tJ _ i_ L _ L i_ ll I  I  I

I  I  I  I

W 6 U 9 0 1 W V 2

0 9 -0 1 P -1 5

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов