manualshive.com logo in svg

Mazda MX-6 1998, Руководство по ремонту

Mazda MX-6 1998 Workshop Manual - руководство по ремонту и обслуживанию автомобиля. Скачайте бесплатно мануал на manualshive.com. Подробное описание всех работ и узлов автомобиля, что позволит вам самостоятельно проводить техническое обслуживание. Улучшите свой автомобиль с помощью нашего руководства.

Поделиться
Скачать
background image

AUTOMATIC TRANSAXLE [GF4A-EL]

05-17B  AUTOMATIC TRANSAXLE [GF4A-EL]

MECHANICAL SYSTEM TEST

 

[G F 4 A -E L ]...............................................0 5 -1 7B -2

Mechanical  System Test Preparation  .  0 5 -1 7B -2
Line  Pressure Test  ............................... 0 5 -1 7B -2

Stall T e s t.................................................0 5 -1 7B -3
Time  Lag  Test  ....................................... 0 5 -1 7B -4

ROAD TEST [G F 4 A -E L ]......................... 0 5 -1 7B -4

Road Test Preparation......................... 0 5 -1 7B -4

Typical  Shift  D iagram ........................... 0 5 -1 7B -4

D  Range T e s t.........................................0 5 -1 7B -5

2  Range T e s t......................................... 0 5 -1 7B -7

1  Range T e s t........................................... 0 5 -1 7 B -7
P  Position Test  ..................................... 0 5 -1 7B -8

AUTOMATIC TRANSAXLE  FLUID (ATF)

INSPECTION  [GF4A-EL]  ..................... 0 5 -1 7 B -8

ATF Condition  Inspection  ................... 0 5 -1 7 B -8
ATF Level  Inspection  ........................... 0 5 -1 7 B -9

AUTOMATIC TRANSAXLE  FLUID  (ATF)

REPLACEMENT [GF4A-EL]  ..................0 5 -17B -10

O/D  OFF SWITCH  INSPECTION

[G F 4 A -E L ]...............................................0 5 -1 7 B -1 0

Inspection  of O peration..........................0 5 -17B -10
Inspection  of Voltage  ............................. 0 5 -17B -10
Inspection  of Continuity..........................0 5 -17B -10

O/D  OFF SWITCH  REMOVAL/INSTALLATION

[G F 4 A -E L ]...............................................05—17B-11

TRANSAXLE RANGE  SWITCH  INSPECTION

[G F 4 A -E L ]...............................................05—17B-11

Inspection  of O peration..........................05-17B-11
Inspection  of Continuity..........................05-17B-11

TRANSAXLE  RANGE SWITCH

 

REMOVAL/INSTALLATION  [GF4A-EL]  05-17B -12

 

TRANSAXLE  RANGE SWITCH  ADJUSTMENT

 

[G F 4 A -E L ]...............................................05—17B-13

TRANSAXLE  FLUID TEMPERATURE SENSOR

INSPECTION  [GF4A-EL]  ........................0 5 -17B -13

TRANSAXLE  FLUID TEMPERATURE  SENSOR

 

REMOVAL/INSTALLATION  [GF4A-EL]  0 5 -17B -14

 

INPUT/TURBINE SPEED SENSOR

INSPECTION  [GF4A-EL]  ........................0 5 -17B -14

INPUT/TURBINE SPEED SENSOR

 

REMOVAL/INSTALLATION  [GF4A-EL]  0 5 -17B -15

 

VEHICLE SPEEDOMETER  SENSOR

INSPECTION  [GF4A-EL]  ........................0 5 -17B -15

VEHICLE SPEEDOMETER  SENSOR

 

REMOVAL/INSTALLATION  [GF4A-EL]  05-17B -16

 

SOLENOID VALVES  INSPECTION

[G F 4 A -E L ]...............................................0 5 -1 7 B -1 6

Inspection of  R e sista n ce

........................05-17B -16

Inspection of O p e ra tio n

..........................05-17B -16

Inspection  of Output  D u t y

...................... 0 5 -1 7 B -1 6

SOLENOID VALVE  REMOVAL/INSTALLATION

[G F 4 A -E L ]...............................................05—17B—17

O/D  OFF  INDICATOR  LIGHT  INSPECTION 

[G F 4 A -E L ]................................................. 0 5 -1 7 B -1 7

Inspection  of O p e ra tio n ..........................0 5 -1 7 B -1 7

Inspection of Voltage  ..............................0 5 -1 7 B -1 7
Inspection of C o n tin u ity .......................... 0 5 -1 7 B -1 8

POWERTRAIN  CONTROL MODULE

INSPECTION  [GF4A-EL]  ........................ 0 5 -1 7 B -1 8

POWERTRAIN  CONTROL  MODULE 

REMOVAL/INSTALLATION  [GF4A-EL]  0 5 -1 7 B -1 8  

AUTOMATIC TRANSAXLE 

REMOVAL/INSTALLATION  [GF4A-EL]  0 5 -1 7 B -1 9

Selector Cable  Removal  Note  .............. 0 5 -1 7 B -2 2
Lower Arm  Removal  N o te ...................... 0 5 -1 7 B -2 2

Tie-Rod  End  Removal  Note  .................. 0 5 -1 7 B -2 2

Drive  Shaft  Removal  N o te ...................... 0 5 -1 7 B -2 2
Engine  Mounting  Member

Removal  N o te ....................................... 0 5 -1 7 B -2 3

Torque  Converter Nuts  Removal  Note  0 5 -1 7 B -2 3
Transaxle  Removal  N o te ........................0 5 -1 7 B -2 3
Transaxle  Installation  N o t e .................... 0 5 -1 7 B -2 4

No.2  Engine  Mount,  Engine  Mount  Member

Installation  Note  ....................................0 5 -1 7 B -2 4

No.1  Engine  Mount  Bolt

Installation  Note  ....................................0 5 -1 7 B -2 5

Joint Shaft  Installation  Note  .................. 0 5 -1 7 B -2 5

Drive Shaft  Installation  N o te .................. 0 5 -1 7 B -2 5
Lower Arm  Installation  Note  .................. 0 5 -1 7 B -2 5

Tie-Rod  End  Installation  N o te ................ 0 5 -1 7 B -2 5

Breather Hose  Installation  N o te ............ 0 5 -1 7 B -2 6
Selector Cable  Installation  N o te ............ 0 5 -1 7 B -2 6

OIL SEAL REMOVAL/INSTALLATION

[G F 4 A -E L ]................................................. 0 5 -1 7 B -2 6

CONTROL VALVE  BODY 

REMOVAL/INSTALLATION  [G F4A-EL]  0 5 -1 7 B -2 6  

OIL COOLER  REMOVAL/INSTALLATION

[G F 4 A -E L ]................................................. 05—17B—28

Oil  Cooler  Installation  N o te .................... 0 5 -1 7 B -2 8
Oil  Pipe  Installation  N o te ........................ 0 5 -1 7 B -2 9
Oil  Hose  Installation  N o t e ...................... 0 5 -1 7 B -2 9

Hose Clamp  Installation  N o te ................ 0 5 -1 7 B -2 9

DRIVE  PLATE  REMOVAL/INSTALLATION

[G F 4 A -E L ]................................................. 0 5 -1 7 B -3 0

Drive  Plate  Mounting  Bolts

Removal  N o te ........................................0 5 -1 7 B -3 0

Drive  Plate  Mounting  Bolts 

Installation  Note  ....................................0 5 -1 7 B -3 0

0 5 -1 7B -1

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Бренд: GARO Страницы: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Бренд: GARO Страницы: 15
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Бренд: Kia Страницы: 419
Quadratec 12226.3011 Installation Manual preview
12226.3011
Бренд: Quadratec Страницы: 8
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Бренд: Connects2 Страницы: 4
Subaru 360 Sedan Service Manual preview
360 Sedan
Бренд: Subaru Страницы: 16
Yakima K1249 Instructions Manual preview
K1249
Бренд: Yakima Страницы: 9
Thule PORTAGE 819 Instructions Manual preview
PORTAGE 819
Бренд: Thule Страницы: 12
Lincoln NAUTILUS 2022 Owner'S Manual preview
NAUTILUS 2022
Бренд: Lincoln Страницы: 586

Бренды по названию

Популярные бренды

Загрузить еще бренды