Mazda MX-6 1998 Скачать руководство пользователя страница 701

Страница: 701 / 1282

TROUBLESHOOTING [LA4A-EL]

STEP

INSPECTION

ACTION

CHECK SENSOR FOR SHORT TO GROUND

• Check for continuity between B A T - (engine

ground) and appropriate jack with an

ohmmeter or other low current tester (less than
200 milliamps).

Solenoid

Tester Jack

TSS

+T S S

-T S S

W6U501WA5

• Connection should show infinite resistance (no

continuity).

• Is there continuity?

Yes

Replace TSS.
Rerun function test.

Go to next step.

CHECK TSS MAGNETISM

• Remove TSS from transaxle.
• Place TSS against a metal surface to which a

magnet would stick. The TSS should be
magnetized and stick to the metal surface.

• Does the TSS stick?

Yes

Go to next step.

Replace TSS.
Rerun functional test.

CHECK EXCITER WHEEL

• Remove TSS.
• With a remote starter, start and stop until a

tooth of the exciter wheel is visible through the
TSS hole. Continue until all 4 teeth have been
visibly inspected.

• Were all teeth present?

Yes

Replace TSS.
Rerun functional test.

Service or replace as required.
Then rerun function test.

Pinpoint test FA

KOEO, KOER

DTC

P1701

Turbine shaft speed (TSS) sensor intermittent

DESCRIPTION

• DTC P1701 is not received during KOEO and KOER self-test but are output during Continuous

Memory self-test and may be intermittent

POSSIBLE

CAUSE

•   Damaged TSS sensor
•   Damaged  harness
•   Damaged  harness connector
•   Damaged  PCM

STEP

INSPECTION

ACTION

FA1

CHECK TSS/ISS OUTPUT WITH NGS TESTER

•   Key off.
•   NGS tester connected.
•   Key on.
•   Monitor TSS/ISS  PID.
•   While observing  PID,  perform the following:

• Tap on sensor to simulate road shock

• Wiggle sensor connector

• Is there any change in rpm reading?

Yes

DISCONNECT and  INSPECT connectors.
If okay,  REPLACE sensor.
RESET  PCM to completely clear DTC.
RERUN  OBD  Test.

Go to next step.

FA2

CHECK PCM VEHICLE HARNESS

• Still monitoring PID.
• While observing appropriate PID, perform the

following:

• Hold the vehicle harness close to the sen

sor connector. Wiggle, shake and bend
small section of wiring harness while work
ing toward PCM.

• Is there any change in rpm reading?

Yes

ISOLATE fault.  SERVICE as  necessary.
RESET  PCM to completely clear  DTC.
RERUN  OBD Test.

Service or replace as required.

Then rerun function test.

0 5 -0 1 A -2 6

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды