Mazda MX-6 1998 Скачать руководство пользователя страница 302 | Manualshive

Страница: 302 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL KL]

STEP

INSPECTION

ACTION

10

CHECK  CONTINUITY OF  POWER  CIRCUIT
CIRCUIT
•   Key off.
•   MAF sensor disconnected.
•   Disconnect  PCM.  Inspect for damaged or

pushed out pins, corrosion, loose wires,

etc. Service as necessary.

• Install breakout box. Leave PCM

disconnected.

• Measure resistance between MAF sensor

connector and Test Pin 71 or 97 at
breakout box.

• Is resistance less than 5.0 ohms?

Yes

Power harness circuit to PCM is okay.

Go to next step.

No

Service open in power harness circuit.

REMOVE breakout box.

RECONNECT all components.
RESET PCM to completely clear DTCs.

¡y

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

11

CHECK  MAF SENSOR  CIRCUIT  FOR
SHORTS TO GROUND  CIRCUIT AND  PCM
GROUND  CIRCUIT
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   PCM  disconnected.
•   Disconnect  NGS tester from  DLC.
•   Measure  resistance between Test  Pin  88

and Test Pins 36 and 24 or 103 at breakout
box.

•

Is each resistance greater than 10,000

ohms?

Yes

MAF signal circuit, PCM ground circuit and ground circuit

harness circuits to PCM are okay.

RECONNECT NGS tester.

Go to next step.

No

Service short circuit between MAF signal circuit and
ground circuit or PCM ground circuit.

REMOVE breakout box.
RECONNECT all components.
RESET PCM to completely clear DTCs.

cr

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

12

CHECK PCM GROUND  CIRCUIT (BETWEEN
PCM AND  MAF SENSOR  GROUND
CIRCUIT)  FOR SHORT TO  GROUND
CIRCUITS.
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   PCM disconnected.

• NGS tester disconnected from DLC.
• Measure resistance between Test Pin 36

and Test Pin 51 or 103 at breakout box.

•

Is each resistance greater than 10,000

ohms?

Yes

RECONNECT NGS tester.

Go to next step.

No

SERVICE  short circuit between  MAF signal circuit and
ground circuit.
REMOVE  breakout box.
RECONNECT all components.
RESET  PCM to completely clear DTCs.

xt

After Repair Procedure

COMPLETE OBD II Drive Mode.

13

CHECK CONTINUITY OF  MAF SIGNAL
CIRCUIT
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   PCM  disconnected.
•   Measure  resistance between  MAF sensor

vehicle harness connector and Test Pin 88
at breakout box.

•

Is resistance less than 5.0 ohms?

Yes

MAF signal harness circuit to PCM is okay.

Go to next step.

No

SERVICE  open  in  MAF signal  harness circuit.
REMOVE  breakout box.
RECONNECT all components.
RESET  PCM to completely clear DTCs.

tt

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

14

CHECK GROUND  CIRCUIT TO  MAF
SENSOR
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   PCM connected to breakout box.

• Key

on,

engine

off.

• Measure voltage between power circuit

and ground circuit at MAF sensor vehicle

harness connector.

• Is voltage greater than 10.5 volts?

Yes

Ground harness circuit from battery negative post to MAF
sensor is okay.
Go to step 4.

No

Go to step 3.

01-01B-96

«
...
300
301
302
303
304
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 4

Бренд: PAC Страницы: 8

Бренд: PAC Страницы: 5

Бренд: Bestop Страницы: 11

Бренд: Whispbar Страницы: 14

2014 Insignia VXR SuperSport

Бренд: Vauxhall Страницы: 56

Бренд: Pacbrake Страницы: 14

Бренд: Farad Страницы: 8

Бренд: Acura Страницы: 2

Бренд: Spiral Audio Страницы: 2

Бренд: BURY Страницы: 2

Бренд: P-Invent Страницы: 4

Бренд: Parkeon Страницы: 43

Бренд: METRON Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды