Mazda MX-6 1998 Скачать руководство пользователя страница 1070 | Manualshive

Страница: 1070 / 1282

background image

TROUBLESHOOTING [SIGNAL LIGHTING SYSTEM]

3

Hazard warning function does not operate (Turn signal function operates)

TROUBLESHOOTING HINTS

Malfunction in hazard warning function power supply circuit

Q Hazard warning lights do not illuminate (Turn signal lights illuminate)

• HAZARD 15 A fuse malfunction
• Malfunction in wiring harness between HAZARD 15 A fuse and flasher unit

Malfunction in hazard warning function operation circuit

© Hazard warning lights do not illuminate (Turn signal lights illuminate)

•   Flasher unit malfunction
•   Hazard warning switch  malfunction
•   Malfunction  in wiring  harness between flasher unit and  hazard warning switch
•   Malfunction  in wiring  harness between hazard warning switch  and ground

STEP

INSPECTION

ACTION

Is HAZARD 15 A fuse okay?

HAZARD

/

15 A FUSE

W6U901WP9

Yes

Go to next step.

No

Replace fuse after repairing wiring harness.

Measure voltage at terminal A at flasher unit

connector of wiring harness.

Is voltage

B+?

Yes

Go to next step.

No

Repair wiring harness between HAZARD 15 A fuse and

flasher unit.

I

G

E

c

A

1

H

F

P - f i l

W 6 U 9 0 1 W P A

Inspect flasher unit.

v

0 9 -1 8 FLASHER UNIT INSPECTION

Is flasher unit okay?

Yes

Go to next step.

No

Replace flasher unit.

c r 0 9 -1 8 FLASHER UNIT REMOVAL/INSTALLATION

Measure voltage at terminal A at hazard
warning switch connector of wiring harness.

Is voltage

B+?

Yes

Go to next step.

" I P

A

No

Repair wiring harness between flasher unit and hazard

warning switch.

f D r a t i

a

1

W 6 U 9 0 1 W P B

0 9 -0 1 L -6

«
...
1068
1069
1070
1071
1072
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Camcar Страницы: 2

Green Motion Building

Бренд: Eaton Страницы: 12

Бренд: Prorack Страницы: 14

Бренд: Pacbrake Страницы: 14

Бренд: TATA Motors Страницы: 156

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

Бренд: Volvo Страницы: 24

Бренд: WABCO Страницы: 52

Evo All THAR-FOR3

Бренд: Fortin Страницы: 7

Electra 225 1965

Бренд: Buick Страницы: 914

DAF CHARGEMAX 90

Бренд: Paccar Страницы: 40

Бренд: Brink Страницы: 26

IT FITS RBO1018

Бренд: RBO Страницы: 36

PRIME DESIGN HRR3-E-PM52

Бренд: Safe Fleet Страницы: 12

Бренд: Westin Страницы: 3

Бренд: Cadillac Страницы: 438

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды