Mazda MX-6 1998 Скачать руководство пользователя страница 703

Страница: 703 / 1282

TROUBLESHOOTING [LA4A-EL]

STEP

INSPECTION

ACTION

CHECK HARNESS FOR SHORT TO POWER
OR GROUND

• Key off.
• Breakout box installed, PCM disconnected.

Caution

• Removing the solenoid body connector by

prying with a screwdriver will damage the

connector. Remove the solenoid body

connector by pushing on the wire tab and

pulling on the wiring harness.

• Solenoid body connector disconnected.
• Refer to connector schematic and table of

solenoid body.

Solenoid Body Connector Component

• Measure resistance between 3-2T/C C S

solenoid circuit test pin 102 and test pin 71/97
at the breakout box.

• Measure resistance between 3-2T/C C S

solenoid circuit test pin 102 and test pins
77/103, 91 at the breakout box.

• Is each resistance greater than 10,000 ohms?

Yes

Inspect  PCM  power relay, service as  required.  If okay,
replace  PCM.
Rerun  OBD test.

Service short circuit.
Remove breakout box.
Reconnect all componets.
Rerun OBD test.

Pinpoint test TB

DTC

P1780

O/D OFF

s w itc h not c ycle d d u rin g se lf-te st

DESCRIPTION

This Pinpoint test is intended to diagnose the following components:

• Transaxle wiring harness, O/D OFF switch, O/D OFF indicator light
• PCM

POSSIBLE

CAUSE

• Electrical: Battery, input sensors, wiring harness
• Transaxle: Linkages

STEP

INSPECTION

ACTION

TB1

DIAGNOSTIC TROUBLE CODE

P1780

• Diagnostic trouble code (DTC) P1780 indicates

the O/D OFF switch was not cycled during key

on engine running (KOER) Self-Test.

Possible cause:

• O/D OFF switch damaged or switch not

cycled during self-test

• Shorted harness
• Damaged PCM

Did O/D OFF switch cycled during KOER
self-test?

Yes

Go to next step.

Return KOER Self-Test to cycle O/D OFF switch.

TB2

CHECK O/D OFF SWITCH CIRCUIT FOR
VOLTAGE

• Key off.
• Disconnect PCM. Inspect for damaged or

pushed out pins, corrosion, loose wires, etc.
Service as necessary.

• Install breakeout box, leave PCM

disconnected.

• Key on engine off.
•

Measure voltage between test pin

and test

pins 24/77 at the breakout box while cycling

the O/D OFF switch several times

Does the voltage cycle?

Yes

Replace PCM.
Remove breakout box.
Rerun OBD test.

Go to next step.

0 5 -0 1 A-2Ô

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды

Mazda MX-6 1998, Руководство по ремонту

Результаты поиска

Содержание MX-6 1998

Отзывы:

Похожие инструкции для MX-6 1998

Бренды по названию

Популярные бренды