Mazda MX-6 1998 Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL KL]

STEP

INSPECTION

ACTION

5

CHECK MAF CIRCUIT  FOR  SHORT TO
GROUND  IN  PCM
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   Reconnect PCM to  breakout box.
•   Disconnect  NGS tester from  DLC.
•   Measure  resistance between Test  Pin 88

and Test Pins 36 and 24 or 103 at breakout
box.

•

Is each resistance greater than 10,000

ohms?

Yes

RECONNECT NGS tester.
Go to next step.

No

MAF signal circuit shorted to MAF sensor ground or PCM

ground circuit in PCM.

REMOVE breakout box.
RECONNECT MAF sensor.
RESET PCM to completely clear DTCs.

f t

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

6

CHECK PCM GROUND CIRCUIT (BETWEEN

PCM AND MAF SENSOR GROUND

CIRCUIT)  FOR  SHORT TO  GROUND
CIRCUIT  IN  PCM
•   Key off.
•   MAF sensor disconnected.
•   Breakout box installed.
•   PCM  connected to breakout box.
•   NGS tester disconnected from  DLC.
•   Measure resistance between Test  Pin 36

and Test Pins 51 or 103 at breakout box.

• Is resistance greater than 10,000 ohms?

Yes

RECONNECT NGS tester.

Go to next step.

No

PCM  ground circuit shorted to ground circuit in  PCM.
REPLACE  PCM.
REMOVE  breakout box.
RECONNECT all components.
RERUN  OBD Test.

7

CHECK MAF SENSOR CIRCUIT OUTPUT

• Key off.

•   MAF sensor connected.
•   Breakout box installed.
•   PCM connected.
•   Key on,  engine running.

Note

• If stabilized idle is not stabilized at

minimum of 700 rpm, go to ENGINE
SYMPTOM TROUBLESHOOTING.

• Measure voltage between Test Pin 88 at

breakout box and battery negative post.

•

Is voltage between 0.34 and 1.96 volts at

idle?

Yes

MAF signal circuit to PCM is okay.
Go to next step.

No

MAF signal circuit or  MAF sensor ground circuit is open  in
MAF sensor,  or MAF signal  circuit is shorted to  PCM
ground circuit in  MAF sensor.

REPLACE  MAF sensor.
REMOVE  breakout box.
RECONNECT  PCM.
RESET PCM to completely clear DTCs.

f t

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

8

VERIFY MAF SENSOR  CIRCUIT INPUT AND
OUTPUT
•   Key off.
•   MAF sensor connected.
•   Breakout box Installed.
•   PCM connected.
•   Key on,  engine  running.
•   Measure voltage between Test  Pin  88 and

Test Pin 36 at breakout box.

•

Is voltage between 0.34 and 1.96 volts?

Yes

PCM ground circuit in MAF sensor is okay.
Go to next step.

No

PCM ground circuit open  in  MAF sensor.
REPLACE  MAF sensor.
REMOVE breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear DTCs.

f t

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

9

CHECK  MAF SENSOR  CIRCUIT OUTPUT
WITH  NGS TESTER
•   Key off.
•   MAF sensor connected.
•   Key on,  engine  running.

• Access MAF PID with

NGS

tester at idle.

• Is

MAF PID

within specified value?

j y 01-40B MASS AIR FLOW SENSOR

INSPECTION [KL]

Yes

Unable to identify fault at this time.
Check possible intermittent.
Go to SYMPTOM TROUBLESHOOTING No.27.

No

MAF sensor signal circuit or PCM ground circuit is open or
shorted together in PCM.

REPALCE  PCM.
REMOVE breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear DTCs.

f t

After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

01-01B -95

«
...
299
300
301
302
303
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: Lancia Страницы: 276

Бренд: T-Tech Страницы: 38

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: JANE Страницы: 21

Vantage 12 Series

Бренд: Ecco Страницы: 5

Бренд: Uebler Страницы: 56

Бренд: Toro Страницы: 24

Бренд: Whelen Engineering Company Страницы: 9

2000 Oldsmobile Intrigue

Бренд: Oldsmobile Страницы: 348

Бренд: Z Flash Страницы: 4

Бренд: QA1 Страницы: 3

Бренд: Subaru Страницы: 16

Бренд: Chevrolet Страницы: 46

Бренд: Quadratec Страницы: 2

Бренд: Honda Страницы: 279

Бренд: EZ-ON Страницы: 2

Бренд: AEV Страницы: 16

Бренд: Whispbar Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды