Mazda MX-6 1998 Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 1282

background image

TROUBLESHOOTING [ENGINE CONTROL KL]

STEP

INSPECTION

ACTION

10

CHECK MAF SIGNAL CIRCUIT OUTPUT

• Key off.

•   MAF sensor connected.
•   Breakout box Installed,  PCM connected.
•   Key on,  engine running.

Note

• If stabilized idle is not stabilized at

minimum of 700 rpm, go to ENGINE
SYMPTOM TROUBLESHOOTING.

• Measure voltage between Test Pin 88 at

breakout box and battery negative post.

•

Is voltage at idle between 0.34 and 1.96

volts?

Yes

MAF signal circuit to PCM is okay.
Go to next step.

No

MAF signal circuit or ground circuit is open in MAF sensor,
or MAF signal circuit is shorted to PCM ground circuit in
MAF sensor.

REPLACE MAF sensor.

REMOVE breakout box.

RECONNECT PCM.
RESET PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

11

VERIFY  MAF SIGNAL CIRCUIT  INPUT AND
OUTPUT
•   Key off.
•   MAF sensor connected.
•   Breakout box installed,  PCM connected.
•   Key on,  engine running.

• Measure voltage between Test Pin 88 and

Test Pin 36 at breakout box.

• Is voltage between 0.34 and 1.96 volts?

Yes

PCM ground circuit in MAF sensor is okay.
Go to next step.

No

PCM  ground circuit  open  in MAF sensor.
REPLACE  MAF sensor.
REMOVE  breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear DTCs.

c r After Repair Procedure

COMPLETE OBD II Drive Mode.

RERUN OBD Test.

12

CHECK MAF SIGNAL CIRCUIT OUTPUT
WITH  NGS TESTER
•   Key off.
•   MAF sensor connected.

• Breakout box Installed, PCM connected.

• Key on, engine running.

• Access MAF PID with NGS tester at idle.
•

Is

MAF PID

within specified value?

e r 01-40B MASS AIR FLOW SENSOR

INSPECTION [KL],

Yes

Unable to  identify fault at this time.
Check possible  intermittent.
Go to  ENGINE  SYMPTOM TROUBLESHOOTING  No.27

No

MAF signal circuit or PCM ground circuit is open or
shorted together in PCM.

REPLACE  PCM.
REMOVE breakout box.
RECONNECT  PCM.
RESET  PCM to completely clear  DTCs.

f t

After Repair Procedure

COMPLETE OBD II Drive Mode.
RERUN OBD Test.

13

CHECK MAF SENSOR OUTPUT VOLTAGE

Note

• DTC P1101 could be generated by low

charged vehicle battery or garage exhaust
ventilation system.  Service battery as
necessary. Then  remove ventilation system
and  properly vent to outside  atmosphere.

Return key on engine off (KOEO) Self-Test.

• Key off.
• Check that MAF sensor in corrected. If not,

service as necessary.

• Disconnect PCM. Inspect for damaged or

pushed out pins, corrosion, loose wires,
etc. Service as necessary.

• NGS tester connected.
• Install breakout box, connect PCM to

breakout box.

• Key on, engine off.
• Measure between Test Pin 88 and Test

Pins 24 or 103 at breakout box.

•

Is voltage greater than 0.20 volts?

Yes

MAF signal voltage is greater than expected.
Go to step 7.

No

Go to step 3.

01-01B-13

«
...
217
218
219
220
221
...
»

Содержание MX-6 1998



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-6 1998

Бренд: ZAPTEC Страницы: 64

Бренд: ZAPTEC Страницы: 24

GRAND CHEROKEE 2023

Бренд: Jeep Страницы: 108

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Бренд: Doug Thorley Headers Страницы: 5

Бренд: Edelbrock Страницы: 2

MagicComfort MSH200

Бренд: Waeco Страницы: 108

Бренд: Tusk Страницы: 2

Бренд: RAM Страницы: 616

Бренд: Nav TV Страницы: 9

Бренд: Honda Страницы: 81

Бренд: Boyo Страницы: 9

inView 360 Fusion

Бренд: Safe Fleet Страницы: 27

ROADSIDE ASSISTANCE

Бренд: Seat Страницы: 44

Бренд: Voxoa Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды